Quick Answer: A Jura drip tray that will not slide back in is most often blocked by a plastic part of the brew unit that did not retract. This happens when the tray comes out during a brewing cycle or right after the machine is switched off. Never force the tray. Take it out, switch the machine on so the brew unit resets itself, then refit the tray and the coffee grounds container together. This cause comes from repair technicians, not from Jura’s manuals. The manuals only tell you not to pull the tray while the machine is brewing.
Repair Service
Tray Still Blocked After a Restart?
Tell us your machine model and what you see in the tray opening. We will look for an experienced Jura repair technician who covers your area. There is no obligation to proceed.
Three Problems, One Area of the Machine
The tray will not go in, the tray will not come out, or the display keeps showing “Empty drip tray” or “Drip tray not fitted”. All three involve the cavity behind the tray, where the brew unit drops used coffee into the grounds container. Our not turning on guide and the troubleshooting hub cover the display side briefly. This page covers the physical problem.
First Rule: Do Not Force the Tray
A tray that stops short has hit something, and the parts behind it are plastic. More force can break a part of the brew unit and turn a free fix into a repair.
Jura’s manuals for the E6, E8, S8, and ENA 8 all carry the same rule in the safety section: “Never pull out the drip tray during the brewing process. Only pull the drip tray when the display instructs you or when the appliance is ready for use.” Most blocked trays start with a break of that rule.
Cause 1: A Brew Unit Part Did Not Retract
This is the most likely cause when you see “a plastic piece that was not there before”.
Where this explanation comes from. Jura’s manuals do not describe this fault. The explanation comes from repair technicians. They report: if you remove the tray right after you switch the machine off, or before a drink has finished, an internal plastic blade from the brew unit has no time to retract, and the tray cannot go fully in. Treat it as the likely cause, not as a statement from Jura.
What happens. After each coffee, the brew unit moves to push the used puck into the grounds container. If the tray leaves the machine during that movement, or the power goes off before the movement ends, the unit can stop away from its rest position. A blade or flap then hangs into the space the grounds container needs.
The tray can also block after it goes in without the grounds container and you make a coffee. The puck lands in the tray or the cavity, and the stack no longer fits.
The fix. The brew unit returns to its rest position when the machine starts up.
- Switch the machine off with the On/Off button.
- Pull the drip tray out. Lift the grounds container off the tray.
- Look into the opening with a flashlight. Remove any loose puck or coffee grounds you can reach. Do not pull on the plastic part.
- Slide the tray in without the grounds container. Stop if it meets resistance.
- Switch the machine on. Let it finish its startup. The part should move back by itself.
- Pull the tray, put the grounds container on it, and slide both in together.
If the empty tray will not go in at step 4, leave it out and switch the machine on anyway. Technicians report that the startup movement still resets the part. The display then asks for the tray. Fit it at that point.
Do not run this restart more than two or three times. If the part does not move, go to the repair section.
Cause 2: The Stack Is Not Assembled Correctly
On the E6, E8, and S8 the tray is a stack of parts. The grounds container sits on the drip tray, and the S8 and ENA 8 manuals also list a separate “insert for drip tray”. The whole stack goes into the machine as one piece.
Jura’s daily maintenance steps in the E8/E80 and S8 manuals put it in one line: “Refit the coffee grounds container and the drip tray.” No step puts the tray in alone for normal use.
Check these points:
- The insert is flat. An insert that sits on its edge raises everything above it.
- The grounds container sits in its place on the tray. If it is turned or tilted, its top edge hits the machine.
- The cup platform is fully down on the front of the tray.
- Nothing is warped or cracked. A part that no longer sits flat needs replacement. That is not a machine fault.
Cause 3: Coffee Behind the Grounds Container
Jura’s troubleshooting table for the E6, E8, and ENA 8 has an entry for this: “There is dry ground coffee behind the coffee grounds container.” Jura gives the cause as beans that produce an above-average volume of ground coffee. The remedy is to reduce the coffee strength or choose a finer grinder setting.
A packed layer of coffee at the back of the cavity can stop the tray a few millimeters short. The tray looks closed, but the machine shows “Drip tray not fitted”.
- Switch the machine off and unplug it.
- Pull the tray and look into the cavity with a flashlight.
- Remove the loose coffee with a dry brush or a vacuum cleaner nozzle. Do not use water inside the machine.
- Wipe the floor of the cavity with a slightly damp cloth and let it dry.
Our brew unit cleaning guide explains why this area collects coffee.
The Tray Is In, but the Machine Does Not Recognize It
There are two different messages. They have different causes.
”Drip tray not fitted”
Jura’s manuals for the E6, E8, S8, and ENA 8 give one cause: “The drip tray is not inserted correctly or is not inserted at all.” The action is “Fit the drip tray.” So the machine believes the tray is out of position. Work through causes 1 to 3 above. Then push the tray in until it stops, with even pressure on both sides.
”Empty drip tray” stays on
Jura’s manuals for the Impressa J9.3 and XJ9 answer this directly. For the problem “‘Empty drip tray’ is always displayed”, the cause is: “The metal contacts of the drip tray are dirty or wet.” The action is: “Clean and dry the metal contacts on the back of the drip tray.” The same manuals include “Dry the metal contacts on the back of the drip tray” in the daily maintenance steps.
The current E6, E8, S8, and ENA 8 manuals do not repeat that line. If your tray has two metal contacts on its back edge, the same care applies. Water or coffee sludge between the contacts reads as a full tray.
- Pull the tray while the machine is switched on.
- Empty it and wash it with warm water and dish soap.
- Clean the two metal contacts. Remove all coffee residue between and around them.
- Dry the contacts and the back of the tray completely.
- Refit the grounds container and the tray.
”Empty grounds” stays on
Jura states this in every manual we checked: “Always empty the coffee grounds container when the machine is switched on. This is the only way of resetting the coffee grounds counter.” If you empty the container while the machine is off, the counter does not reset and the message returns.
Empty the container each time the tray comes out. A container that overfills piles pucks above its rim, and that jams the tray.
The error codes guide and the symbols guide show how these messages appear on each display type.
The Tray Will Not Come Out
Jura’s manuals have no procedure for a stuck tray. The steps below are our own, built on the manual’s rule about when to pull it.
- Check the machine state. The machine must be on and ready, or the display must ask for the tray. If it is rinsing or brewing, wait.
- Pull straight and level. Hold the tray at both sides. Use a small side-to-side movement. Do not lift the front, and do not use a tool as a lever.
- Restart once. If the tray moves a little and then stops, something behind it holds it. Switch the machine off, wait for it to stop, and switch it on again. The brew unit resets during startup. Try the tray again when the machine is ready.
- Stop there. More force breaks the tray or the part behind it.
Model Notes
- E6 and E8. The E6 message table lists “Empty coffee grounds container” and “Drip tray not fitted”. The E8 table adds “Empty drip tray”. Parts suppliers list two versions of the E6/E8/S8 tray, so match your machine’s model number before you order a replacement.
- S8. The manual lists three parts: drip tray, insert for drip tray, and coffee grounds container. The newer S8 manual lists “Empty coffee grounds container / Empty drip tray” and “Drip tray not fitted”.
- ENA 8. A smaller tray with its own insert. The messages are “Empty grounds / Empty drip tray” and “Drip tray not fitted”.
When Is It a Repair Job?
The checks above cost nothing. These results mean the fault is inside the case:
- The plastic part stays in the opening after two or three restarts. The brew unit is not completing its movement. A motor noise followed by a stop, or an error number on the display, points the same way. See Error 8 for the brew unit position fault.
- A part is bent or broken because the tray was forced.
- “Drip tray not fitted” stays on with the tray fully home and the cavity clean. Technicians trace this to the tray detection inside the machine. Jura’s manuals give no user step beyond “Fit the drip tray”.
- “Empty drip tray” stays on with clean, dry contacts. The contacts on the tray or in the machine are corroded, or the fault is in the wiring behind them.
Do not open the case. The brew unit is not removable by the owner. The repair vs replace guide has the cost by fault type.
Repair Service
Need a Technician for a Blocked Tray?
Tell us the model, what the display shows, and what happened when you restarted the machine. We will look for an experienced Jura repair technician who covers your area. There is no obligation to proceed.
Frequently Asked Questions
Why will my Jura drip tray not go back in?
The likely cause is a plastic part of the brew unit that did not retract. Repair technicians report it. Do not force the tray. Take it out, switch the machine on so the brew unit resets, then refit the tray.
There is a plastic piece in the tray opening that was not there before. What is it?
Technicians describe it as a blade or flap of the brew unit. It hangs into the grounds container space when the brew unit stops away from its rest position. Do not pull on it. Switch the machine on with the tray out.
Can I run a Jura without the coffee grounds container in the tray?
No. The used puck then falls into the tray or the cavity. Jura’s manuals say to refit the coffee grounds container and the drip tray together.
Why does “Empty drip tray” stay on when the tray is empty?
Jura’s Impressa manuals give the cause: the metal contacts of the drip tray are dirty or wet. Clean and dry the contacts on the back of the tray.
What does “Drip tray not fitted” mean when the tray is in?
Jura’s manuals say the tray is not inserted correctly. Look for loose coffee behind the grounds container, an insert that is not flat, or a brew unit part in the way.
My Jura drip tray is stuck and will not come out. What now?
Do not lever it. Wait until the machine is ready. Pull straight and level. If it does not move, restart the machine once and try again.
Related
- Jura Not Turning On - when the tray prompt stops the startup
- Jura Error 8 - the brew unit position fault
- Jura Brew Unit Cleaning Guide - what happens behind the tray
- Jura Troubleshooting Quick Diagnosis - symptom table for all models