Quick Answer: Jura’s GIGA machines use their own error table, so the same number can mean a different fault than on an E8 or Z10. Error 11 means the right grinder’s Hall sensor sends no pulses (the grinder does not turn, or the sensor failed). Error 13 means the right grinder cannot start. Error 17 means the brew unit cannot reach its position. Home Jura models never show codes 11, 12, 13, 16, 17, 18, 19, 20 or 21. If you see one of them, you have a GIGA, or you are reading the display wrong. The full table and the first steps to try are below.
Repair Service
GIGA showing an error that will not clear?
Tell us the GIGA model, the error number and your location. We look for a technician who services the GIGA in your area. No obligation.
Which Machines Use the GIGA Code Table?
Jura’s technician error-code reference (a German repair document, linked in the sources below) gives the GIGA family its own table. It covers the GIGA 5, GIGA W3, GIGA X3, GIGA X7, GIGA X8 and GIGA X9. Not every code applies to every one of these models.
The newer GIGA 6 and GIGA 10 are not in that reference. They are also GIGA machines, but check the text on the display and your instructions for use before you rely on a number from this table.
Home Jura machines (E, S, Z, J, ENA and WE lines) use the general table. That table only has codes 0 to 10, plus 14, 15, 22 and 23. Our Jura error codes guide covers those.
The Full GIGA Error Table
| Code | What it means on a GIGA | Parts the reference names |
|---|---|---|
| 1 | Coffee temperature sensor reads too low | Sensor, power board, logic board; thermoblock defective or heavily scaled |
| 2 | Coffee temperature sensor reads too high; brewing stopped for safety | Machine too cold, or sensor, thermal fuse, heater, boards |
| 3 | Speed (bypass hot water) temperature sensor reads too low | Sensor, boards; thermoblock defective or heavily scaled |
| 4 | Speed temperature sensor reads too high | Machine too cold, or sensor, thermal fuse, heater, boards |
| 5 | Steam temperature sensor reads too low | Sensor, boards; thermoblock defective or heavily scaled |
| 6 | Steam temperature sensor reads too high | Machine too cold, or sensor, thermal fuse, heater, boards |
| 7 | Steam wand temperature sensor reads too low | Sensor, boards; thermoblock defective or heavily scaled |
| 8 | Steam wand temperature sensor reads too high | Machine too cold, or sensor, thermal fuse, heater, boards |
| 9 | No heating: coffee brewing temperature not reached | Sensor, thermal fuse, boards; thermoblock defective or heavily scaled |
| 10 | No pulses from the left grinder’s Hall sensor | Left grinder does not turn, or its Hall sensor failed |
| 11 | No pulses from the right grinder’s Hall sensor | Right grinder does not turn, or its Hall sensor failed |
| 12 | Left grinder cannot be initialized | Grinder microswitch, cable, boards or grinder |
| 13 | Right grinder cannot be initialized | Grinder microswitch, cable, boards or grinder |
| 14 | CAPPU (milk) stepper motor cannot be initialized | Cable, stepper motor, boards |
| 15 | Venting stepper motor cannot be initialized | Cable, stepper motor, boards |
| 16 | Ceramic multi-way valve cannot position or initialize | Valve, boards. See our Error 16 guide |
| 17 | Brew unit cannot position or initialize | O-rings, motor, transformer, encoder, drain valve, boards |
| 18 | Logic relay defective | Logic board |
| 19 | Heater overheated (mains interference pulses received) | Sensor, interference filter, boards |
| 20 | Controller timeout between logic and display | Component cable, display, logic board |
| 21 | Controller timeout between logic and display RTC | Component cable, display, logic board |
| Fan symbol | The fan does not work | Fan or logic board |
Error 11 and Error 10: A Grinder That Does Not Turn
The GIGA has two grinders. A Hall sensor on each one counts its turns, so the machine knows the grinder is running. Error 11 means the right grinder’s sensor sent no pulses. Error 10 is the same fault on the left grinder.
The reference gives two causes: the grinder does not turn at all, or it turns but its sensor failed. The fix in the reference is to remove the grinder and the Hall sensor, check them, and replace what failed. That work is inside the case.
What you can check first, without opening anything:
- Which hopper is affected. Note whether the fault appears with a drink that uses the right bean container. That tells the technician which grinder to look at.
- Foreign objects. A small stone or a broken bean in the hopper can block a grinder. Empty that bean container and look for anything that is not a bean.
- Restart once. Switch off at the main switch, unplug for five minutes, and restart. If the code comes straight back, stop and book a technician. Repeated attempts on a jammed grinder can damage it.
Error 13 and Error 12: A Grinder That Will Not Start
Error 13 means the machine could not start the right grinder. Error 12 is the same fault on the left grinder. Unlike Error 10 and 11, the grinder does not get as far as turning. The reference names the grinder microswitch, a cable, the power board, the logic board or the grinder motor.
Do the same three checks as for Error 11. If the code returns after a restart, a technician must test the switch, the cable and the motor in turn.
Error 17: The Brew Unit Cannot Reach Its Position
Error 17 is the GIGA’s brew unit fault, and it matches Error 8 on home models. The reference gives three situations:
- The brew unit moves stiffly. The usual cause is swollen or torn O-rings. The fix is new O-rings and fresh lubrication of the brew unit.
- The brew unit does not move. A transformer, motor, cable contact or board has failed.
- The brew unit is in the wrong position. The reference names the drain valve, the brew unit itself, the encoder and its cable, the motor, a guide roller or a board.
Case 1 is the most common and the cheapest repair. It still needs the brew unit taken out and serviced, so it is a technician job on a GIGA. Regular cleaning tablet cycles and on-time descaling slow O-ring wear.
Temperature Codes 1 to 9: Check the Room First
For the “reads too high” codes (2, 4, 6 and 8) and for Error 9, the reference gives one owner step first: let the machine reach normal room temperature. A GIGA that was delivered in winter, or stored in a cold room or a car, can trip these codes until it warms up.
If the machine is at room temperature and the code returns after a restart, the reference points to a sensor, the thermal fuse, the heater or a board. A heavily scaled thermoblock is also on the list for codes 1, 3, 5, 7 and 9, so a machine with a long gap since its last descaling cycle needs a technician to check for scale.
What to Tell the Technician
A GIGA quote is faster and more accurate when you give:
- The exact model (GIGA 5, X3, X8 and so on). It is on the type plate.
- The error number, and whether it appears at start-up or during a drink.
- For grinder codes, which bean container the failing drink uses.
- When the machine was last descaled and whether a CLARIS filter is fitted.
Repair Service
Need a Jura Repair Technician?
Tell us your machine, the problem, and your location. We will look for an experienced repair technician who covers your area. There is no obligation to proceed.
Frequently Asked Questions
What does Error 11 mean on a Jura?
Error 11 is a GIGA code: no pulses from the right grinder’s Hall sensor. The right grinder does not turn, or its sensor failed. Home Jura models do not use code 11.
What does Error 13 mean on a Jura GIGA?
The right grinder cannot be initialized. The reference names the grinder microswitch, a cable, the power board, the logic board or the grinder. Error 12 is the same fault on the left grinder.
What does Error 17 mean on a Jura GIGA?
The brew unit cannot be positioned or initialized. Stiff movement usually comes from swollen or torn O-rings. It is the GIGA equivalent of Error 8 on home models.
Why does Error 10 mean something different on my GIGA?
The GIGA has its own table. On home models Error 10 is a heater overheated by mains interference. On the GIGA, Error 10 is the left grinder’s Hall sensor, and the overheating fault is Error 19.
Can I fix a Jura GIGA error code myself?
Let the machine reach room temperature, then switch off at the main switch, unplug for five minutes and restart. For grinder codes, also empty the affected bean container and look for foreign objects. If the code returns, the fault is inside the case and needs a technician.
Related
- Jura Error Codes Guide - the general table for home models
- Jura Error 16 - the GIGA ceramic valve fault in detail
- Jura Error 8 - the home-model brew unit fault (GIGA Error 17)
- Jura Repair Cost and Options